For a standard 60 by 90 cm bed pad the backsheet should be a 25 to 30 gsm film; if you want the breathable version it has to be pad grade rated at 80 cmH2O or better. Below that rating the film still feels soft and still reads "breathable" on the datasheet, but it has no margin against the 4 kPa load that the leakage test puts on it.
We have run this product line for more than twenty years, and the same enquiry arrives several times a month with the same pattern. Two suppliers answer one RFQ with "breathable film, 25 gsm" and "PE film, 25 gsm"; the price gap looks like a quality gap, and neither datasheet names a hydrostatic rating. At the sample stage the two films feel the same in the hand. The difference shows up when a hospital spot checks a wet pad, or when a distributor opens a carton after a 30 day voyage and finds damp sheets.
The backsheet is the cheapest component in a pad and the easiest one to respecify without a test. What follows is the arithmetic we use when deciding which film belongs on a pad, and where breathability stops paying.
What the backsheet does on a bed pad
Three jobs, in order: hold liquid inside the core, keep the core from shifting when a patient moves, and give the converting line enough tensile to run at speed without snapping at a splice. On a pad with adhesive tabs it also carries the tab.
Notice what is not on that list: the underpad backsheet does not touch skin, the topsheet does. On a pad the film faces the mattress, so vapour that passes through it goes into a mattress rather than room air. That is why the breathability case cannot be transplanted unchanged from a brief: on a brief the path ends in open air, on a pad it ends in whatever the bed is covered with.
The two films on one table
Plain PE film is a continuous cast or blown film. No pores means no liquid path and no vapour path. Microporous breathable film starts as a PE compound loaded with calcium carbonate, stretched in the machine direction until the filler debonds and leaves a connected pore network roughly 0.5 to 2.0 µm across, mostly between 0.5 and 1.5 µm. A water droplet is orders of magnitude larger than the pore, a vapour molecule far smaller. That is the whole mechanism, as one film supplier explains.
| Property | Plain PE film | Breathable PE film, pad grade |
|---|---|---|
| Structure | Continuous film, no pores | Calcium carbonate filled, machine direction stretched, connected pores |
| Basis weight | 20 to 30 gsm | 25 to 30 gsm for pads (supplier range 12 to 30 gsm) |
| Thickness at 25 gsm | About 27 µm at a PE density of 0.92 g/cm³ | Lower than plain film at the same gsm, because filler replaces polymer |
| Water vapour transmission | No rated vapour path | 2,000 to 8,000 g/m²·24h to GB/T 1037, 38 °C and 90% RH |
| Hydrostatic head | Not applicable, no pore path | At least 80 cmH2O |
| Pore size | None | 0.5 to 2.0 µm, more than 95% between 0.5 and 1.5 µm |
| Hand and noise | Stiffer, rustles | Softer, quieter |
| Print and adhesive | Wetting tension check before printing or gluing | Same check, corona treatment fades with age |
Basis weight is the first line that gets lost. Calcium carbonate has a density near 2.7 g/cm³ against 0.92 for PE, so equal grams means a thinner, weaker web once filler is counted, which is why pad grade breathable film starts at 25 gsm rather than 20.
The second line is the grade. Film suppliers publish different hydrostatic targets for sanitary pads, baby diapers and underpads. The pad target is the highest of the three, not the middle one. A quotation that says only "breathable film" does not tell you which of the three you are buying, and the sample stage will not reveal it. The spot check will.
The number that decides the grade: 4 kPa against 80 cmH2O
GB/T 28004.2-2021 covers adult diapers, inserts and underpads, and its leakage step is a pressure test. After the second dose of test liquid, 15 layers of absorbent paper go on the pad and a standard weight applies 4.0 ± 0.2 kPa for one minute. Liquid that reaches the paper is measured as leakage. The acceptance line for a pad is stricter than for a diaper. An adult diaper is allowed up to 1.0 g of leakage in a 2026 comparative test run to that standard; a pad has to show no seepage and no leakage at all.
4.0 kPa is 408 mm of water column. Put the film datasheets next to it.
| Film grade | Hydrostatic head | In mm of water | In kPa | Margin over the 4 kPa test |
|---|---|---|---|---|
| Sanitary pad grade | 30 cmH2O | 300 mm | 2.9 kPa | 0.74 |
| Baby diaper grade | 60 cmH2O | 600 mm | 5.9 kPa | 1.47 |
| Underpad grade | 80 cmH2O | 800 mm | 7.8 kPa | 1.96 |
A sanitary film at 30 cmH2O is under the test load before the pad starts absorbing, and the margin of 0.74 says exactly that. A baby diaper film at 60 cmH2O gives 1.47. The pad grade at 80 cmH2O gives 1.96, and that is the number we lock on our own orders.
The margin is not decoration. Urine is not clean water: soap, barrier cream and cleanser residues lower surface tension, and a lower surface tension breaks through a given pore at a lower pressure. Folding does the same locally, and so does a saturated core under a hip. A film with no margin has nothing left to absorb that. It is also the only reason we refuse the phrase "sanitary film works just as well" on a pad project: the money saved does not cover one return shipment.
Ask for the test conditions as well as the number. Hydrostatic head is read while the water column climbs, and the method behind these films, GB/T 24218.16, climbs at 600 mmH2O per minute. A slower ramp reads higher on the same sample. Two suppliers can both quote 80 cmH2O and be quoting two different tests, which is why we only accept film data that carries its test conditions.
Moisture vapour transmission needs the same discipline. A figure of 2,000 g/m²·24h means nothing without the condition: GB/T 1037-2021 dry cup runs at 38 °C and 90% RH, 60 mm cup, 35 g of desiccant, air at 0.3 to 0.5 m/s. The same film reads lower at 23 °C and 50% RH. A number with no condition attached is marketing until the test report arrives.
Where breathable film earns its money
The clinical case for breathability is real, and it comes from briefs rather than pads. A 2010 study in BMC Geriatrics measured skin hydration after four hours under different panel materials and found that an air permeable nonwoven above 1,200 L/m²/s avoided the over hydration seen under air impermeable film. In the same programme, 8 of 12 patients with existing dermatitis resolved after the ward switched to the redesigned brief. That paper puts dermatitis prevalence between 5.7% and more than 42% of incontinent patients, by care setting.
Read the mechanism rather than the headline. Vapour leaves because the panel has somewhere to vent. On a bed pad the vent is the mattress, and a waterproof protector closes it. Under a protector, a breathable backsheet has no outlet and behaves like a slightly more expensive PE film with a softer hand. We have seen this repeatedly in programmes for European and North American care home operators: what actually keeps the bed surface dry is the air permeability of the mattress cover, not the four figure MVTR on the backsheet datasheet.
Four situations still justify the premium:
- Home care and hospice, where the same patient lies on the pad for hours and humidity peaks at each repositioning.
- Rooms above 26 °C, which covers the Gulf and much of West Africa for half the year.
- Patients with existing skin breakdown, where any extra heat and moisture slows healing.
- Tenders that name a breathable underpad backsheet as a listing requirement, where the specification stands even if the physics is indirect.
In those cases, specify 30 gsm at 80 cmH2O and pair it with a breathable mattress cover. Without the cover the money is spent on a datasheet.
What breathability cannot fix
If the complaint is a damp sheet under the pad, the film is not the first suspect. Dampness at the end of a shift is usually rewet: the core releasing liquid under body weight, with the liquid finding the fold lines and the embossed edge seal, where the web has been stressed. A breathable film is not a valve. It passes vapour, not liquid.
Odour follows the same logic: a microporous film is not an odour barrier, and ammonia is small enough to travel with the vapour. If odour is the complaint, the levers are core pH, SAP choice and change frequency.
Tearing at the edge during transfer is a third failure, a matter of film tensile and notch sensitivity at the cut, and unrelated to breathability. We covered it in a separate guide on edge tear.
Frequently asked questions
Is a breathable backsheet worth it on an underpad?
Only when three things are true at once: the film is pad grade at 80 cmH2O or better, the mattress underneath can vent, and the patient is in bed for long stretches with existing skin risk. Take one of those away and a plain 25 gsm PE film does the same job for less money.
Can I use sanitary pad film on an underpad?
Not on a pad that has to pass a leakage test. Sanitary film is rated around 30 cmH2O, and the underpad test loads 4 kPa, which is 408 mm of water column. The film is already past its rating before the core has taken up the second dose.
Why does the underside of my underpad feel damp?
Rewet first, film second. The core releases liquid under body weight and it finds the fold lines before it finds a pore. Measure rewet in grams on a sample from the same lot, and check the core and the topsheet before you change the underpad backsheet.
What gsm backsheet should a 60 by 90 cm underpad use?
25 to 30 gsm. Below 25 the tensile and puncture margin gets thin for a pad that is tucked and dragged. Above 30 you are paying for film the pad does not need, and the extra weight buys nothing at the leakage test.
Does breathable film leak under a patient's weight?
It leaks when the rating sits below the load, or when the core is saturated in one spot and the film is creased under a hip. At 80 cmH2O the margin over the 4 kPa test is about 1.9 times, which is where we set the floor. Weight alone is not the problem; pressure on a wet crease is.
Quick Summary
Spec the underpad backsheet by grade, not by the word breathable: 25 to 30 gsm, 80 cmH2O if you go breathable. If the mattress cannot vent, buy PE film.
About Tianjin Wholesome Hygiene Products Co., Ltd.
Focused on the development and manufacture of disposable hygiene products since 1996, with 15 production lines and more than 150 employees. The range covers adult diapers, pull-ups, underpads, pet pads and menstrual pants, supplied to B2B buyers worldwide on an OEM/ODM basis. Underpad programmes can be configured with the backsheet specification and matching test reports appropriate to each market: hospitals, care home operators, and retail private label.