DOWNLOAD CATALOG

The ADL in Adult Diapers: Four Formats, Four Different Jobs

A tape-type brief and a booster pad can carry the same 45 gsm acquisition layer and behave nothing alike on the wearer. The material is identical. The fluid path is not.

Publish Time:

That is the first thing worth fixing in most procurement conversations. Buyers tend to write one ADL line, paste it across the range, and then wonder why a pull-up draws a side-leak complaint the brief never had, or why a booster that tested well in the lab wets back through at hour six. The specification did not fail. The specification was written for a different geometry.

This note sets out how we spec the adult diaper ADL across the four formats we run — tape-type briefs, pull-ups, underpads and booster inserts — and where the numbers actually come from.

What the layer is being asked to do in an adult product

An adult void is larger and arrives faster than the infant case most layer guides are built around. On a brief in a lying position, that volume now has the full length of the product to travel before the core accepts it, and the core is competing with a standing leg cuff that is only millimetres away.

Three duties, restated in adult terms:

Intercept. Hold the incoming volume for the two or three seconds the core needs to start swelling. Not absorb it — hold it, with air.

Spread. Move liquid along the machine direction and across the width so the core wets by area. A core that gels under the urethra and nowhere else is finished for the night, and the SAP beyond it never works at all.

Buffer. Keep a dry, lofted gap between a saturated core and the topsheet while the wearer sits, turns, or is repositioned by a carer. This is the duty that separates a layer that works from one that merely exists.

Nothing on that list is storage. If the complaint is "full by morning", the lever is core SAP and pulp, not the ADL. If the complaint is a wet surface at change time, urine reaching the cuff before it soaks in, or a wearer who feels damp within twenty minutes of a change, the acquisition distribution layer is the first component to inspect.

Four formats, four different jobs

Format How the insult arrives What the ADL must do What fails when it is underspecified
Tape-type brief Gravity-fed, load concentrated at the crotch; wearer sitting or lying for hours Intercept fast, spread along MD, hold loft under sustained body weight Wet topsheet at change; liquid rides the cuff before the core takes it
Pull-up Same volume, but the core is compressed by a 360° elastic waistband on every donning Stay anchored under cyclic shear, keep even width after stretch, avoid creasing Layer migrates and folds into a channel; side leak at the leg opening
Underpad Open system — no containment of any kind, load lands at one point Spread laterally and fast, before liquid reaches an edge Pooling in a small radius; run-off at the border
Booster insert Receives liquid that has already passed a topsheet, then sits under a second product Pass through quickly with low resistance, low rewet under double compression Backflow to skin; the pad bunches and "swims" between layers

Three of these differences are worth spelling out, because each one changes what purchase order you should be writing.

In a pull-up, the acquisition layer is bonded into a laminate that is stretched every time the product is put on. A layer that is only laid down will creep, and a crease in a 1.3 mm web is a channel. Our pull-up range uses a wider anchorage pattern than the equivalent brief for that reason, and the ADL is inspected after lamination, not just on the roll.

An underpad has no backsheet to save it and no cuff to slow liquid down. The layer has to do the spreading alone, which pushes the width up and the density gradient down. The engineering for that format is specific enough that we treat it separately — the capillary-channel design behind our disposable underpads is covered in its own technical note.

A booster is the opposite extreme. It carries no backsheet of its own and sits inside another product, so the layer is asked to release rather than retain, under a double compression load. Our booster and insert range runs a lower-density web for exactly that reason: here the constraint is flow resistance, not capacity.

Three numbers, and the one that goes missing

Three numbers define the acquisition distribution layer, and buyers normally ask for one. Ask for grammage and you will get grammage. Ask for all three and you can predict the product.

Format Basis weight Loft Apparent density
Tape-type brief 40–50 gsm 1.1–1.5 mm ≤ 38 kg/m³
Pull-up 35–45 gsm 1.0–1.3 mm ≤ 38 kg/m³
Underpad 30–40 gsm 1.0–1.4 mm ≤ 32 kg/m³
Booster insert 45–55 gsm 1.0–1.3 mm ≤ 42 kg/m³

Work the arithmetic once and the reason becomes obvious. Take a 130 × 450 mm adult patch at 45 gsm and 1.3 mm. The area is 0.0585 m², so the fibre mass is 2.63 g. The geometric volume is 0.0585 × 1.3, or about 76 cm³. Polypropylene at 0.91 g/cm³ occupies roughly 2.9 cm³ of that. The remaining 73 cm³ is air, and that air is the entire product benefit.

Now press the same roll to 0.9 mm — which is what happens when a web is wound too tight, or when a lower grammage is substituted without re-checking loft. Volume drops to about 53 cm³ and free space to roughly 50 cm³. Apparent density climbs from 35 to 50 kg/m³. Grammage, price and delivery note are unchanged. A third of the buffer is gone and nothing on the paperwork shows it.

This is why we do not quote a spec line as "45 gsm". A number without a thickness is not a specification; it is a weight.

Where an adult ADL fails in the field

Every failure below is a failure of the acquisition distribution layer as built, not as quoted — which is why five of them are invisible on the purchase order.

Cuff wicking at high void volume. An ADL wider than the core hands liquid to the standing cuff and manufactures the leak it was bought to prevent. We hold the ratio at 80–95% of core width and state it on the drawing.

Width drift between sample and production. Slitting tolerance is a real production variable. A sample at 120 mm and a production roll at 126 mm is a three-week delay on the water before anyone notices.

Collapse under sustained load. Adult wearers sit for long stretches and carers reposition them; a wet web at 2 kPa for hours does not spring back. Thickness retention after saturation is the number that predicts this, and it is worth reading alongside our wet-compression data for underpad ADL rather than treating it as a footnote.

Lamination shear in pull-ups. The layer is elastic-bonded at tension. If the adhesive pattern is narrow, the ADL travels relative to the core over a shift and gathers at one end.

Night dwell. A day brief is changed in four hours; a night product runs eight to twelve. The second and third voids meet a web that has already been wetted and loaded once, which is why first-dose performance tells you the least about the product that actually matters.

What we check on every incoming roll

The material arrives before the diaper exists, so this is the only place a deviation is cheap to catch. Six checks, every lot:

  1. Basis weight — 100 × 100 mm die cut, 0.01 g balance, three specimens, average within ± 7% of the approved value.
  2. Thickness at 2 kPa — dead-weight foot, three readings per roll, minimum held against the drawing rather than the label.
  3. Apparent density — calculated, and compared with the approved sample, not with the supplier's certificate alone.
  4. Width and core diameter — measured, matched to the slitting instruction.
  5. Splice count per roll — counted and flagged with tape, because an unflagged splice is a stop on a high-speed line.
  6. Retained sample — one length per lot held twelve months against the golden sample.

A roll that reads 45 gsm at 0.9 mm is rejected regardless of what the delivery note says. That single rule has done more for our complaint rate than any supplier negotiation.

The compliance layer most buyers skip

Two items come up in audits more often than they should.

The standard number on the certificate. China's GB/T 28004 series splits by product: Part 1 covers baby diapers, Part 2 covers adult incontinence products. The limits are set separately and are not interchangeable. A supplier certificate quoting Part 1 test results is not evidence that your adult line was tested at all — and buyers do accept these documents without reading the part number.

Change control. In the EU, adult incontinence products sit inside the medical device framework, and the ADL is a component in the technical file. Changing the material source, the grammage or the fibre blend is a documented change with a re-assessment behind it, not a purchasing decision taken over email to hit a price. Under ISO 13485 the same event triggers component re-approval and finished-product re-validation.

Manufacturing since 1996, we run this through a documented change procedure on 15 production lines with a team of 150+, under ISO 9001, ISO 13485, ISO 14001, ISO 45001 and GMPC, with FDA facility registration and CE-marked technical files for the European range. When a buyer asks to downgrade an adult diaper ADL to hit a price, that request goes through the same route as any other design change — which is usually the point at which the conversation becomes useful.

The arithmetic that actually decides it

At USD 3.00/kg, the 45 gsm patch above costs about USD 0.008 per piece. At 30 gsm with the loft adjusted honestly, it costs about USD 0.005. On a million pieces that is USD 2,600 saved.

What it buys is roughly 48 cm³ of buffer instead of 73 cm³, on a product whose entire job in the last three hours of the night is that buffer. A single container held at destination for a rewet claim — re-testing, storage, the retail conversation, the replacement shipment — costs more than USD 2,600 before anyone has agreed who pays for it. And the letter that opens the claim will not mention the layer at all. It will say the product feels wet, and it will arrive five weeks after the container clears port.

Our position on the full incontinence range is straightforward: we will quote a cheaper ADL when a buyer asks for one, and we will put the resulting buffer volume in the quotation next to the price, so the trade is visible. For an adult diaper ADL, that is the only honest way to present the saving.

What we will and will not do in an OEM brief

We will specify grammage, loft, apparent density, width ratio, fibre type and splice handling on the drawing, and test the incoming roll against all of it. We will keep lot samples for twelve months and produce a documented change record if the material moves. We will run a sample in seven days and finalise artwork in three.

We will not change an ADL source mid-order without written change control, and we will not accept a purchase order that names a grammage and nothing else — because we have seen what that produces at destination, and it is never the layer the buyer thinks they bought.

Our tape-type brief programme, including the ADL-bearing functional version, starts at 20,000 pieces per size in XS to XXXXL; underpads at 50,000 per size from 33 × 45 cm up to 90 × 180 cm; booster inserts from 220 × 500 mm to 355 × 740 mm. Loading from Tianjin and Qingdao, EXW through DDP, with FBA delivery support.

FAQ

Is the ADL the same in a pull-up and a brief? 

No. The fluid duty is similar; the mechanical duty is not. A pull-up layer is loaded in cyclic shear every time the product is put on, so anchorage and crease resistance matter more than raw loft. We run 35–45 gsm in pull-ups against 40–50 gsm in briefs for that reason.

Does a higher grammage give a drier surface? 

Not by itself. Surface dryness tracks free volume and the interface with the core, not weight. A 50 gsm web pressed to 0.9 mm holds less air than a 40 gsm web at 1.3 mm, and it will feel wetter at change time.

Can one ADL specification cover my whole range? 

Within a format, usually yes. Across formats, no — an underpad needs more width and lower density than a brief, and a booster needs lower flow resistance than either. Four lines, four jobs.

How do I verify a roll without a lab? 

A 100 × 100 mm die cut, a 0.01 g balance and a dead-weight thickness gauge at 2 kPa will separate good material from compressed material in ten minutes. Multiply the weighed grams by 100 for grammage; divide grammage by thickness in metres and again by 1,000 for apparent density in kg/m³. Reject on the pair, never on the weight alone.

What does changing the ADL cost me in compliance? 

A documented change, a component re-approval and a finished-product re-validation, plus the technical file update if you sell in the EU. It is a two-line email to ask for and a six-week exercise to complete. Price it before you ask.


Wholesome Hygiene — Tianjin Wholesome Hygiene Products Co., Ltd. OEM/ODM adult incontinence and disposable hygiene manufacturing since 1996. 15 production lines, 150+ staff, 40+ export markets. ISO 9001, ISO 13485, ISO 14001, ISO 45001, GMPC; FDA facility registration; CE technical files.

Request a free sample and a 24-hour quotation

Related Products

Pull-on Disposable Period Underwear

pull-on disposable period underwear with 360 elastic waistband for supermarkets

Specs Tags:360° Elastic Waistband | 12-Hour Leak-Proof Protection | High-Volume Retail Supply

Product Copy:Underwear-style pull-on menstrual pants utilizing a 360-degree stretchy waistband and highly absorbent core. Provides discreet, secure protection up to 12 hours, perfect for international retail chains, supermarket brokers, and B2B hygiene brand importers.

 

Panty Liners

organic cotton panty liners bulk supply for international pharmacy chains

Specs Tags:Ultra-Thin Breathable Backsheet | Fluorescent-Free Topsheet | Daily Feminine Care

Product Copy:Ultra-thin and highly breathable panty liners designed for daily freshness and light discharge. Crafted with certified fluorescent-free raw materials to ensure maximum skin safety. Perfect for pharmacy distributors and retail supermarket chains.

Wet Wipes

Wet Wipes

Specs Tags: Soft Embossed Non-Woven Fabric | Mild Skin-Friendly Lotion | Multi-Scenario Cleansing

Product Copy: Crafted for gentle yet powerful daily cleaning, adopting premium thick non-woven cloth and balanced moisturizing formula. Delivers even moisture lock and lint-free wiping performance, ideal for baby care, household and travel retail clients.

Straight-type Maternity Pads

economical straight-type maternity pads bulk supply for late-stage postpartum care

Specs Tags:Ultra-Soft Cotton Topsheet | Highly Absorbent Core | Late-Stage Postpartum Care

Product Copy:High-utility straight-type maternity towels designed for secure, late-stage postpartum care with reduced lochia volume. Features a large absorption surface, skin-friendly material, and full-length back adhesives, perfect for bulk wholesale and pharmacy distribution.

WRITE TO US

Request A Free Quote

Get a Customized Solution Tailored to Your Needs

As a leading adult diaper factory in China, Wholesome Hygiene provides cost-effective bulk pricing, wholesale adult diapers, and low-MOQ private label options designed to grow your brand. Don't hesitate to reach out. Contact our B2B team today to request a free quote and start your customization journey!

Flexible Solutions 24H Services Expert Support

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details